Simer Pumps 5020B-04 Manuel d'utilisateur télécharger pdf (Page 3)

Safety 3

For parts or assistance, call Simer Customer Service at 1-800-468-7867

DESCRIPTION

This Pedestal Sump Pump is designed for home

sumps. Unit is equipped with a 3-prong grounding-

type power cord. Sleeve bearings on motor shaft never

need lubrication. Automatic reset thermal protection.

NOTICE: This unit is not designed for applications

involving salt water or brine! Use with salt water or

brine will void warranty.

SPECIFICATIONS

Power supply required ........................115V, 60 HZ.

Horsepower ........................................................1/3

Motor duty .............................................Intermittent

Liquid Temp. Range ...............32°F to 70°F(0°-21°C)

Individual Branch Circuit

Required GFCI Class A...............................15 Amps

Motor full load (maximum) .......................3.5 Amps

Discharge:.............................................1-1/4" FNPT

PERFORMANCE

GENERAL SAFETY

Electrically powered sump pumps normally give many

years of trouble-free service when correctly installed,

maintained, and used. However, unusual circum-

stances (interruption of power to the pump, dirt/debris

in the sump, flooding that exceeds the pump’s capaci-

ty, electrical or mechanical failure in the pump, etc.)

may prevent your pump from functioning normally. To

prevent possible water damage due to flooding, con-

sult your retailer about a secondary AC sump pump, a

DC backup sump pump, and/or a high water alarm.

See the “Troubleshooting Chart” in this manual for

information about common sump pump problems and

remedies. For more information, see your retailer or

call Simer customer service at 1-800-468-7867.

1. Know the pump application, limitations, and

potential hazards.

Do not use in explosive

atmospheres. Pump water

only with this pump. Failure to follow this warn-

ing can result in personal injury and/or property

damage.

2. Disconnect power before servicing.

3. Release all pressure within system before servic-

ing any component.

4. Drain all water from system before servicing.

Risk of flooding. If a flexible dis-

charge hose is used, pump may

move when motor starts. If it moves far enough so

that switch hits side of sump, switch may stick and

prevent pump from starting.Make sure pump is

secured so it cannot move around in sump.

5. Secure discharge line before starting pump. An

unsecured discharge line will whip, possibly

causing personal injury and/or property damage.

6. Check hoses for weak or worn condition before

each use, making certain all connections are

secure.

7. Inspect sump, pump and system components

monthly. Keep free of debris and foreign

objects. Perform routine maintenance as

required.

FIRE HAZARD - Do not store

or rest objects on or near

motor or switch linkage. Keep all flammable

objects or liquids away from motor.

8. Provide means of pressure relief for pumps

whose discharge line can be shut-off or

obstructed.

9. Personal Safety:

a. Wear safety glasses at all times when work-

ing with pumps.

b. Keep work area clean, uncluttered and

properly lighted – replace all unused tools

and equipment.

c. Keep visitors at a safe distance from work

area.

d. Make workshop child-proof – with pad-

locks, master switches, and by removing

starter keys.

10. When wiring an electrically driven pump, fol-

low all electrical and safety codes, as well as

most recent National Electrical Code (NEC) and

Occupational Safety and Health Act (OSHA).

11. This equipment is only for use on 115 volt (sin-

gle phase) and is equipped with an approved 3-

conductor cord and 3-prong, grounding-type

plug.

To reduce risk of electric

shock, be certain that it is

connected to properly grounded, grounding-

type receptacle.

Never connect green (or

green and yellow) wire in

cord to a live terminal!

Where a 2-prong wall receptacle is encoun-

tered, it must be replaced with properly

grounded 3-prong receptacle installed in accor-

dance with the National Electrical Code and

local codes and ordinances.

12. All wiring should be performed by a qualified

electrician.

13. Make certain that power source conforms to

requirements of your equipment.

14. Protect electrical cord from sharp objects, hot

surfaces, oil, and chemicals. Avoid kinking

cord. Replace or repair damaged or worn cords

immediately.

15. Do not touch an operating motor. Modern

motors are designed to operate at high temper-

atures.

16. Do not handle pump or pump motor with wet

hands or when standing on wet or damp sur-

face, or in water.

If your basement has water or

moisture on floor, do not walk on

wet area until all power has been turned off. If

shut-off box is in basement, call electric company

to shut-off service to house, or call local fire

department for instructions. Remove pump and

repair or replace. Failure to follow this warning

can result in fatal electrical shock.

Do not use in hazardous or

explosive locations.

GPH (LPH) AT TOTAL FEET (M)

5 Ft. 10 Ft. 15 Ft. 20 Ft.

(1.52) (3.05) (4.57) (6.09)

3000 2460 1620 0

(11 355L) (9 312L) (6 131L) (0L)

1 2 3 4 5 6 7 8 ... 15 16

Commentaires sur ces manuels

Pas de commentaire

Simer Pumps 5020B-04 Manuel d'utilisateur Page 3

Commentaires sur ces manuels

Produits connexes et manuels pour Pompes à eau Simer Pumps 5020B-04

Související produkty a manuály pro Hráči Aiwa UZ-PS128